PDA

View Full Version : Got my dyno results today!!!


tiffo60
10-10-2006, 02:53 PM
In 80 degree shop temps with 70% humidity and 14 degrees of timing it put down 490hp @ 582tq not bad considering the conditions, thursday suppose to be cooler temps so im going to dyno again on race tune with 110, and hopefully the low humidity and cooler air will get me over 500hp




http://www.svtgalleries.net/gallery/data/500/tiffs_dyno_pull-001.jpg
L-Fever
10-10-2006, 03:06 PM
Not bad for a stock block! :tu:
99WhiteBeast
10-10-2006, 04:53 PM
Not bad for a stock block! :tu:

+1:eek: :tex
bluesvt
10-10-2006, 04:55 PM
Awesome! :beer:
Mark #2
10-10-2006, 05:06 PM
Where is the A/F?, only reason I ask is that the tq seems to fall off too much for that combination.
tiffo60
10-10-2006, 05:08 PM
Where is the A/F?, only reason I ask is that the tq seems to fall off too much for that combination.

there air to fuel wasnt working but terry tuned it saturday and it was 11.3 to 11.6
mk5.0
10-10-2006, 05:19 PM
Where is the A/F?, only reason I ask is that the tq seems to fall off too much for that combination.

Nice numbers...

But I would still check the A/F.. Usa is haveing a free dyno this weekend I believe
Mark #2
10-10-2006, 05:23 PM
there air to fuel wasnt working but terry tuned it saturday and it was 11.3 to 11.6

Okay cool, my charts are at work.
I will look at the curves tomorrow
tiffo60
10-10-2006, 05:31 PM
Okay cool, my charts are at work.
I will look at the curves tomorrow

cool cool, im sure terry will chime in too
RSVT
10-10-2006, 05:43 PM
Not bad for a stock block! :tu:

do you have a built motor? or is it still stock, either way nice #'s dude:bows :tu:
REXRENEGADE
10-10-2006, 06:18 PM
Tiffton you are going to be damn near doin WHEELIES!
:burnout:
tiffo60
10-10-2006, 07:26 PM
do you have a built motor? or is it still stock, either way nice #'s dude:bows :tu:


stock block:tex
Highlander540
10-10-2006, 07:56 PM
Nice Job :beer:
04SVTRACING
10-10-2006, 08:29 PM
Thats freakin awesome Tifton knana .

His truck runs like a raped ape, I must say. I rode with him out to Frisco last night. Its definetly fast.....put a beating on a few vehicles as well.
StormShadow
10-10-2006, 08:40 PM
Daaaaang! Way more than mine put down at 17lbs. :beer:
L8 APEX
10-10-2006, 08:48 PM
And he dares ask for a race tune, oh well customer is always right.. I think everyone should use this dyno from now on;) . Who needs A/F:evil
tiffo60
10-10-2006, 08:55 PM
And he dares ask for a race tune, oh well customer is always right.. I think everyone should use this dyno from now on;) . Who needs A/F:evil

hows the graph look, should we set up a dynotune?
Ohmsby
10-10-2006, 09:00 PM
nice #'s I am going to speedworks on Thursday to get mine done:tongue:
02BOLT
10-10-2006, 09:22 PM
Nice numbers Tifton!:eek: Just be careful.:tu:
True Blue Aggie
10-10-2006, 09:58 PM
Tifton...

You should come out to Ennis on Sunday to run the 1/4..... Then you'll have dyno and 1/4 mile numbers..
BC Lightning
10-10-2006, 10:04 PM
nice #'s I am going to speedworks on Thursday to get mine done:tongue:

Its HPP now, speedworks went under some time ago :rolleyes:
Ohmsby
10-10-2006, 10:19 PM
Its HPP now, speedworks went under some time ago :rolleyes:

I stand corrected:)
WA 2 FST
10-10-2006, 11:45 PM
I stand corrected:)

If you're that close, take it to RPM instead. Just my $.02.
L-Fever
10-11-2006, 06:44 AM
If you're that close, take it to RPM instead. Just my $.02.

+1
FRDRCING
10-11-2006, 06:26 PM
Nice numbers tifton
wesman
10-11-2006, 10:34 PM
I must say that I don't trust that dyno much. This is the same dyno that everyone was reading 40-50hp low back at the dyno day correct? They jsut didn't seem to be quite up to speed on it.

Head on out to USA dyno on Sat morning. I plan on going out there to dyno with the nitrous.


--wes
tiffo60
10-12-2006, 08:19 AM
I must say that I don't trust that dyno much. This is the same dyno that everyone was reading 40-50hp low back at the dyno day correct? They jsut didn't seem to be quite up to speed on it.

Head on out to USA dyno on Sat morning. I plan on going out there to dyno with the nitrous.


--wes

i may do it
GoldLS1
10-12-2006, 08:44 AM
What time?? Ill drop by....