Wanted Autologic chip

[Mark #2]

Tell me what ya'll have sitting around the house.

I have an extra Diablo sport 3 way chip.

[Silver_2000]

Do I still have the PSP 4 way or did I sell it ???

Ill have to check ....

[Mark #2]

Do I still have the PSP 4 way or did I sell it ???

Ill have to check ....
See this thread:
http://www.talonclub.com/forum/showthread.php?t=3938&highlight=chip

[ThunderBolt]

Do I still have the PSP 4 way or did I sell it ???

Ill have to check ....
You sold it. :D

[wesman]

I have an autologic 4-way but I'm not sure which way I'm going with the truck when it gets a motor in it as I have a JDM flip chip as well.

If you're still looking in a few weeks let me know.

--wes

[Mark #2]

I have an autologic 4-way but I'm not sure which way I'm going with the truck when it gets a motor in it as I have a JDM flip chip as well.

If you're still looking in a few weeks let me know.

--wes
Wes, I have a JDM(Superchips) flip chip too, who are you using for burns?
Mark.

[wesman]

The JDM can be burned by Terry I believe. I had mine burned by JDM according to my dyno charts. The Autologic was tuned by Swanson for the KB

--wes

[Mark #2]

The JDM can be burned by Terry I believe. I had mine burned by JDM according to my dyno charts. The Autologic was tuned by Swanson for the KB

--wes
Wes,
Perfect I have a KB, could I borrow it for a dyno run? What kind of parameters, timing, fuel octane, etc.?

Mark

[wesman]

To be honest I don't know anymore for sure. I could probably call Swanson and see if they have the exact perameters for it.

My rough recollections are something like this:

1 was KB with stock KB pulley and 2 lb lower
1 was KB with 3.25" KB pulley and 4 lb lower
1 was KB with 3.25" KB pulley and 6 lb lower
Last was KB with 3.25" KB pulley and 6 lb lower with race gas

Again, not certain on those at all. Would probably have to contact Swanson and see if they still have the info on file.

--wes

[Mark #2]

To be honest I don't know anymore for sure. I could probably call Swanson and see if they have the exact perameters for it.

My rough recollections are something like this:

1 was KB with stock KB pulley and 2 lb lower
1 was KB with 3.25" KB pulley and 4 lb lower
1 was KB with 3.25" KB pulley and 6 lb lower
Last was KB with 3.25" KB pulley and 6 lb lower with race gas

Again, not certain on those at all. Would probably have to contact Swanson and see if they still have the info on file.

--wes
Wes,
Sounds great the only problem would be my computer. I have a 2000 CUX2 with a 90MAF. If you call Swanson, as him what he thinks about me running on my truck. I am running the 3.25 upper with a 4lb lower, stock bottom end, long tubes and High flow cats.

Mark

[wesman]

That wont be an issue at all...I also have a '00 with 90mm MAF w/ long tubes and high flow cats :)

[Mark #2]

That wont be an issue at all...I also have a '00 with 90mm MAF w/ long tubes and high flow cats :)
Wes,
Wow, great, I would really appreciate borrowing the chip. I have over $1.5K in chips that I'm not overly pleased with.
Mark

[wesman]

Mark,

No problem. However, I assume no responsibilty for the chip or anything on it, use at your own risk and all that jazz:throw:


Where do you live/work ? I live in S. Arlington but work in downtown Dallas M-T

--wes

[Mark #2]

Mark,

No problem. However, I assume no responsibilty for the chip or anything on it, use at your own risk and all that jazz:throw:


Where do you live/work ? I live in S. Arlington but work in downtown Dallas M-T

--wes
Wes,
I am an engineer too(looked at your profile) and I work at TI at 75 and 635. No issues on the risk and responsibility. Maybe a lunch at Bonedaddy's next week?
Mark